NAME

r.buffer - Creates a raster map layer showing buffer zones surrounding cells that contain non-zero category values.
(GRASS Raster Program)

SYNOPSIS

r.buffer
r.buffer help
r.buffer [-q] input=name output=name distances=value[,value,...] [units=name]

DESCRIPTION

r.buffer creates a new raster map layer showing buffer (a.k.a. "distance" or "proximity") zones around all cells that contain non-zero category values in an existing raster map layer. The distances of buffer zones from cells with non-zero category values are user-chosen. Suppose, for example, that you want to place buffer zones around roads. This program could create the raster map layer shown below on the right based on road information contained in the raster map layer shown on the left. 
000000000000000000000000 222233333333333333444444 
111000000000000000000000 111222222222223333333333 
000111111111100000000000 222111111111122223333333 
000000001000011100000000 332222221222211122222222 
000000001000000011111111 333333321233222211111111 
000000001000000000000000 433333321233333222222222 
000000001000000000000000 444443321233333333333333 
000000001000000000000000 444443321233443333333333 
000000001000000000000000 444443321233444444444444 
Category 0: No roads Category 1: Road location 
Category 1: Roads Category 2: Buffer Zone 1 around roads 
Category 3: Buffer Zone 2 around roads 
Category 4: Buffer Zone 3 around roads

INTERACTIVE PROGRAM USE

The user can run the program interactively by simply typing r.buffer without program arguments on the command line. The program then prompts the user for parameter values.
  1. You are requested to identify the existing raster map layer from which distance-from calculations shall be based, and a name (of your choice) for the new raster map layer which will contain the results.
  2. Then, identify the units of measurement in which buffer (distance) zones are to be calculated, and the distance of each buffer zone from each non-zero cell in the input map. The user has the option of identifying up to 60 continuous zones. The zones are identified by specifying the upper limit of each desired zone (r.buffer assumes that 0 is the starting point). ("Continuous" is used in the sense that each category zone's lower value is the previous zone's upper value. The first buffer zone always has distance 0 as its lower bound.) Distances can be entered in one of four units: meters, kilometers, feet, and miles.
  3. Last, calculate distances from cells containing user-specified category values, using the "fromcell" method. [The "fromcell" method goes to each cell that contains a category value from which distances are to be calculated, and draws the requested distance rings around them. This method works very fast when there are few cells containing the category values of interest, but works slowly when there are numerous cells containing the category values of interest spread throughout the area.]

NON-INTERACTIVE PROGRAM USE

The user can run r.buffer specifying all parameter values on the command line, using the form:

r.buffer [-q] input=name output=name distances=value[,value,...]

Flags:

-q
Run quietly

Parameters:

input=name
The name of an existing raster map layer whose non-zero category value cells are to be surrounded by buffer zones in the output map.
output=name
The name assigned to the new raster map layer containing program output. The output map will contain buffer zones at the user-specified distances from non-zero category value cell in the input map.
distances=value[,value,...]
The distance of each buffer zone from cells having non-zero category values in the input map.
units=name
The unit of measurement in which distance zone values are to be calculated. Possible choices for name are: meters, kilometers, feet, and miles. The default units used, if unspecified by the user, are meters.

EXAMPLE

In the example below, the buffer zones would be (in the default units of meters): 0-10, 11-20, 21-30, 31-40 and 41-50.
Format:
r.buffer [-q] input=name output=name distances=value[,value,...]
Example:
r.buffer input=map.in output=map.out distances=10,20,30,40,50 units=meters

NOTES

r.buffer measures distances from center of cell to center of cell using Euclidean distance measure for planimetric databases (like UTM) and using ellipsoidal geodesic distance measure for latitude/longitude databases.

r.buffer calculates distance zones from all cells having non-zero category values in the input map. If the user wishes to calculate distances from only selected input map layer category values, the user should run (for example) r.reclass prior to r.buffer, to reclass all categories from which distance zones are not desired to be calculated into category zero.

SEE ALSO

g.region
r.mapcalc
r.reclass

AUTHORS

Michael Shapiro, U.S. Army Construction Engineering Research Laboratory
James Westervelt, U.S. Army Construction Engineering Research Laboratory